diff --git a/arch/arm/dts/logicpd-som-lv-35xx-devkit.dts b/arch/arm/dts/logicpd-som-lv-35xx-devkit.dts
index f7a841a..f690bc8 100644
--- a/arch/arm/dts/logicpd-som-lv-35xx-devkit.dts
+++ b/arch/arm/dts/logicpd-som-lv-35xx-devkit.dts
@@ -9,5 +9,19 @@
 
 / {
 	model = "LogicPD Zoom OMAP35xx SOM-LV Development Kit";
-	compatible = "logicpd,dm3730-som-lv-devkit", "ti,omap3";
+	compatible = "logicpd,dm3730-som-lv-devkit", "ti,omap3430", "ti,omap3";
+};
+
+&omap3_pmx_core2 {
+
+	hsusb2_2_pins: pinmux_hsusb2_2_pins {
+		pinctrl-single,pins = <
+			OMAP3430_CORE2_IOPAD(0x25f0, PIN_OUTPUT | MUX_MODE3)            /* etk_d10.hsusb2_clk */
+			OMAP3430_CORE2_IOPAD(0x25f2, PIN_OUTPUT | MUX_MODE3)            /* etk_d11.hsusb2_stp */
+			OMAP3430_CORE2_IOPAD(0x25f4, PIN_INPUT_PULLDOWN | MUX_MODE3)    /* etk_d12.hsusb2_dir */
+			OMAP3430_CORE2_IOPAD(0x25f6, PIN_INPUT_PULLDOWN | MUX_MODE3)    /* etk_d13.hsusb2_nxt */
+			OMAP3430_CORE2_IOPAD(0x25f8, PIN_INPUT_PULLDOWN | MUX_MODE3)    /* etk_d14.hsusb2_data0 */
+			OMAP3430_CORE2_IOPAD(0x25fa, PIN_INPUT_PULLDOWN | MUX_MODE3)    /* etk_d15.hsusb2_data1 */
+		>;
+	};
 };
diff --git a/arch/arm/dts/logicpd-som-lv-37xx-devkit.dts b/arch/arm/dts/logicpd-som-lv-37xx-devkit.dts
index a604d92..e28e962 100644
--- a/arch/arm/dts/logicpd-som-lv-37xx-devkit.dts
+++ b/arch/arm/dts/logicpd-som-lv-37xx-devkit.dts
@@ -11,3 +11,17 @@
 	model = "LogicPD Zoom DM3730 SOM-LV Development Kit";
 	compatible = "logicpd,dm3730-som-lv-devkit", "ti,omap3630", "ti,omap3";
 };
+
+&omap3_pmx_core2 {
+
+	hsusb2_2_pins: pinmux_hsusb2_2_pins {
+		pinctrl-single,pins = <
+			OMAP3630_CORE2_IOPAD(0x25f0, PIN_OUTPUT | MUX_MODE3)            /* etk_d10.hsusb2_clk */
+			OMAP3630_CORE2_IOPAD(0x25f2, PIN_OUTPUT | MUX_MODE3)            /* etk_d11.hsusb2_stp */
+			OMAP3630_CORE2_IOPAD(0x25f4, PIN_INPUT_PULLDOWN | MUX_MODE3)    /* etk_d12.hsusb2_dir */
+			OMAP3630_CORE2_IOPAD(0x25f6, PIN_INPUT_PULLDOWN | MUX_MODE3)    /* etk_d13.hsusb2_nxt */
+			OMAP3630_CORE2_IOPAD(0x25f8, PIN_INPUT_PULLDOWN | MUX_MODE3)    /* etk_d14.hsusb2_data0 */
+			OMAP3630_CORE2_IOPAD(0x25fa, PIN_INPUT_PULLDOWN | MUX_MODE3)    /* etk_d15.hsusb2_data1 */
+		>;
+	};
+};
diff --git a/arch/arm/dts/logicpd-som-lv-baseboard.dtsi b/arch/arm/dts/logicpd-som-lv-baseboard.dtsi
index 100396f..7d0468a 100644
--- a/arch/arm/dts/logicpd-som-lv-baseboard.dtsi
+++ b/arch/arm/dts/logicpd-som-lv-baseboard.dtsi
@@ -51,6 +51,8 @@
 
 &mcbsp2 {
 	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mcbsp2_pins>;
 };
 
 &charger {
@@ -77,7 +79,7 @@
 };
 
 &dss {
-	status = "ok";
+	status = "okay";
 	vdds_dsi-supply = <&vpll2>;
 	vdda_video-supply = <&video_reg>;
 	pinctrl-names = "default";
@@ -102,35 +104,18 @@
 		regulator-max-microvolt = <3300000>;
 	};
 
-	lcd0: display@0 {
-		compatible = "panel-dpi";
-		label = "28";
-		status = "okay";
-		/* default-on; */
+	lcd0: display {
+		/* This isn't the exact LCD, but the timings meet spec */
+		compatible = "logicpd,type28";
 		pinctrl-names = "default";
 		pinctrl-0 = <&lcd_enable_pin>;
-		enable-gpios = <&gpio5 27 GPIO_ACTIVE_HIGH>;	/* gpio155, lcd INI */
+		backlight = <&bl>;
+		enable-gpios = <&gpio5 27 GPIO_ACTIVE_HIGH>;
 		port {
 			lcd_in: endpoint {
 				remote-endpoint = <&dpi_out>;
 			};
 		};
-
-		panel-timing {
-			clock-frequency = <9000000>;
-			hactive = <480>;
-			vactive = <272>;
-			hfront-porch = <3>;
-			hback-porch = <2>;
-			hsync-len = <42>;
-			vback-porch = <3>;
-			vfront-porch = <2>;
-			vsync-len = <11>;
-			hsync-active = <1>;
-			vsync-active = <1>;
-			de-active = <1>;
-			pixelclk-active = <0>;
-		};
 	};
 
 	bl: backlight {
diff --git a/arch/arm/dts/logicpd-som-lv.dtsi b/arch/arm/dts/logicpd-som-lv.dtsi
index b56524c..385bc8d 100644
--- a/arch/arm/dts/logicpd-som-lv.dtsi
+++ b/arch/arm/dts/logicpd-som-lv.dtsi
@@ -27,6 +27,8 @@
 
 	/* HS USB Host PHY on PORT 1 */
 	hsusb2_phy: hsusb2_phy {
+		pinctrl-names = "default";
+		pinctrl-0 = <&hsusb2_reset_pin>;
 		compatible = "usb-nop-xceiv";
 		reset-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>; /* gpio_4 */
 		#phy-cells = <0>;
@@ -144,6 +146,8 @@
 };
 
 &usbhshost {
+	pinctrl-names = "default";
+	pinctrl-0 = <&hsusb2_pins>, <&hsusb2_2_pins>;
 	port2-mode = "ehci-phy";
 };
 
@@ -153,8 +157,6 @@
 
 
 &omap3_pmx_core {
-	pinctrl-names = "default";
-	pinctrl-0 = <&hsusb2_pins>;
 
 	mmc3_pins: pinmux_mm3_pins {
 		pinctrl-single,pins = <
@@ -166,6 +168,7 @@
 			OMAP3_CORE1_IOPAD(0x21d2, PIN_INPUT_PULLUP | MUX_MODE3)	/* mcspi1_cs2.sdmmc_clk */
 		>;
 	};
+
 	mcbsp2_pins: pinmux_mcbsp2_pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x213c, PIN_INPUT | MUX_MODE0)        /* mcbsp2_fsx */
@@ -183,6 +186,7 @@
 			OMAP3_CORE1_IOPAD(0x2198, PIN_OUTPUT | MUX_MODE4)	/* GPIO_162,BT_EN */
 		>;
 	};
+
 	mcspi1_pins: pinmux_mcspi1_pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x21c8, PIN_INPUT | MUX_MODE0)        /* mcspi1_clk.mcspi1_clk */
@@ -250,13 +254,13 @@
 };
 
 &omap3_pmx_wkup {
-	pinctrl-names = "default";
-	pinctrl-0 = <&hsusb2_reset_pin>;
+
 	hsusb2_reset_pin: pinmux_hsusb1_reset_pin {
 		pinctrl-single,pins = <
 			OMAP3_WKUP_IOPAD(0x2a0e, PIN_OUTPUT | MUX_MODE4)	/* sys_boot2.gpio_4 */
 		>;
 	};
+
 	wl127x_gpio: pinmux_wl127x_gpio_pin {
 		pinctrl-single,pins = <
 			OMAP3_WKUP_IOPAD(0x2a0a, PIN_INPUT | MUX_MODE4)		/* sys_boot0.gpio_2 */
@@ -265,21 +269,6 @@
 	};
 };
 
-&omap3_pmx_core2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&hsusb2_2_pins>;
-	hsusb2_2_pins: pinmux_hsusb2_2_pins {
-		pinctrl-single,pins = <
-			OMAP3630_CORE2_IOPAD(0x25f0, PIN_OUTPUT | MUX_MODE3)            /* etk_d10.hsusb2_clk */
-			OMAP3630_CORE2_IOPAD(0x25f2, PIN_OUTPUT | MUX_MODE3)            /* etk_d11.hsusb2_stp */
-			OMAP3630_CORE2_IOPAD(0x25f4, PIN_INPUT_PULLDOWN | MUX_MODE3)    /* etk_d12.hsusb2_dir */
-			OMAP3630_CORE2_IOPAD(0x25f6, PIN_INPUT_PULLDOWN | MUX_MODE3)    /* etk_d13.hsusb2_nxt */
-			OMAP3630_CORE2_IOPAD(0x25f8, PIN_INPUT_PULLDOWN | MUX_MODE3)    /* etk_d14.hsusb2_data0 */
-			OMAP3630_CORE2_IOPAD(0x25fa, PIN_INPUT_PULLDOWN | MUX_MODE3)    /* etk_d15.hsusb2_data1 */
-		>;
-	};
-};
-
 &uart2 {
 	interrupts-extended = <&intc 73 &omap3_pmx_core OMAP3_UART2_RX>;
 	pinctrl-names = "default";